Difference between revisions of "Components Previously on the PCB"
| Line 2: | Line 2: | ||
==Components Removed In Spring 2020== | ==Components Removed In Spring 2020== | ||
| − | Prior to spring 2020, the PCB was | + | Prior to spring 2020, the PCB was designed for use by both CUBike and CUSail, resulting in many parts that were not necessary for the functioning of the bike. In Spring 2020, a major overhaul was started in part to remove many of these unnecessary parts. |
| + | ===Watchdog=== | ||
| + | The Watchdog is an external timer circuit that assured the Arduino DUE was correctly executing its loop. The Watchdog’s timer was reset each time the DUE successfully completed a loop. However, if the DUE’s loop execution was unsuccessful, the Watchdog’s timer would not be reset, causing an emergency shutdown and preventing damage to the bike’s systems. | ||
| − | === | + | The Watchdog connected to the PCB through three pins, labeled WD+DPINS, and an op-amp. |
| + | '''WD+DPINS''' | ||
| + | PIN LABEL CONNECTED TO | ||
| + | 1 DUE pin 45 | ||
| + | 2 DUE pin 43 | ||
| + | 3 Op-Amp pin 1 (WDO) | ||
| + | '''Associated Op-Amp''' | ||
| + | PIN LABEL CONNECTED TO | ||
| + | 1 WDO WD+DPINS pin 3 | ||
| + | 2 GND GND | ||
| + | 3 EN DUE pin 41 | ||
| + | 4 WDI DUE pin 42 | ||
| + | 5 VCC C35 --> GND | ||
| + | |||
| + | The Watchdog and associated hardware were removed because an unsuccessful loop execution by the DUE was deemed to be an unlikely source of failure. | ||
| + | |||
| + | ===Additional Components Only Used by CUSail=== | ||
====Sail Motor==== | ====Sail Motor==== | ||
The old PCB contained outputs for the sail motor and bike motor. Since the bike is not a sailboat, the sail motor outputs were removed. | The old PCB contained outputs for the sail motor and bike motor. Since the bike is not a sailboat, the sail motor outputs were removed. | ||
Revision as of 19:19, 18 April 2020
The printed circuit board has many components that have been deemed obsolete and removed. Below is a list of those components, how they worked, and why the were removed.
Contents
Components Removed In Spring 2020
Prior to spring 2020, the PCB was designed for use by both CUBike and CUSail, resulting in many parts that were not necessary for the functioning of the bike. In Spring 2020, a major overhaul was started in part to remove many of these unnecessary parts.
Watchdog
The Watchdog is an external timer circuit that assured the Arduino DUE was correctly executing its loop. The Watchdog’s timer was reset each time the DUE successfully completed a loop. However, if the DUE’s loop execution was unsuccessful, the Watchdog’s timer would not be reset, causing an emergency shutdown and preventing damage to the bike’s systems.
The Watchdog connected to the PCB through three pins, labeled WD+DPINS, and an op-amp. WD+DPINS PIN LABEL CONNECTED TO 1 DUE pin 45 2 DUE pin 43 3 Op-Amp pin 1 (WDO) Associated Op-Amp PIN LABEL CONNECTED TO 1 WDO WD+DPINS pin 3 2 GND GND 3 EN DUE pin 41 4 WDI DUE pin 42 5 VCC C35 --> GND
The Watchdog and associated hardware were removed because an unsuccessful loop execution by the DUE was deemed to be an unlikely source of failure.
Additional Components Only Used by CUSail
Sail Motor
The old PCB contained outputs for the sail motor and bike motor. Since the bike is not a sailboat, the sail motor outputs were removed.
Sail Power
Similar to the sail motor, only the bike power output is necessary.
H-Bridges
Xbee Pro
The Xbee Pro was used in conjunction with CUSail's remote controller. The bike uses a different controller.
